1. Process feasibility analysis of new project (technology, quality) 2. Equipment technical specification 3. Supplier scheme and quotation review 4. Commissioning operation data and problem points 5. Release of process documents

1. College degree or above, mechanical, electromechanical, material, automobile, electronics, etc 2. At least 2 years experience in product design and development in automotive electronics industry, sensor industry is preferred

1. Demand analysis: Analyze hardware design requirements according to customer requirements, draw circuit block diagram, electrical connection diagram, etc; Formulate hardware design scheme according to the project plan. 2. Design of key technical documents: Be responsible for the drawing, modification, improvement and self debugging of schematic diagram; Be responsible for the preparation of sample BOM list, DFMEA, product characteristic list and control plan, and filing data of hardware design; Responsible for hardware circuit worst case analysis (WCA); Responsible for PCB design requirements. 3. Schematic diagram review: Collect and prepare relevant data for schematic diagram review; Organize schematic diagram review and output review report. 4. Hardware design and verification: According to the design requirements and product characteristics, complete the design and verification of hardware circuit, and output the design specification and verification specification; Conduct sample confirmation, select sealed samples and provide relevant standards for quality inspection. Responsible for the production of integrated chips, diodes and triodes, extraction and design of strong relevant parameters, and proofreading of part acknowledgement attached with specifications 5. Test instruction: Guide hardware tester skills and working methods 6. Maintenance tracking: Responsible for technical support and related design maintenance after early introduction and mass production of new products. 7. Project plan: Assist project manager to make project hardware plan

1. Bachelor degree or above, major in circuit and system, automation, electronics, etc 2. At least 3 years hardware design experience in automotive transmission TCU 3. Have experience in hardware circuit design of automobile gearbox TCU; 4. Familiar with Infineon / St solenoid valve drive circuit design 5. Familiar with transmission sensor signal acquisition circuit design; 6. Experience in Infineon aurix chip design; 7. Familiar with cadence / AD, PSPICE and other circuit design software; 8. Understand automotive electronic function safety related knowledge.

Reserve direction: logistics management, project management and quality management

Bachelor degree or above, major in science and engineering, strong pressure resistance, good communication skills and self-motivated. Clear logic, good at analyzing and solving problems

1. Process feasibility analysis of new project (technology, quality) 2. Equipment technical specification 3. Supplier scheme and quotation review 4. Commissioning operation data and problem points 5. Release of process documents

1. Bachelor degree or above 2. Electrical / mechanical and other related majors 3. At least 2 years process development experience in sensor industry 4. Knowledge of pouring and welding, final inspection, assembly and development 5. Five quality tools (p-fmea, APQP, PPAP, SPC, MSA)

1. Be able to communicate effectively with customers and explain the pump design principle and design theory 2. Design capacity of electronic water pump / oil pump: The assembly engineer outputs the requirements to the pump body engineer; The assembly engineer outputs the motor requirements to the motor engineer; Output controller requirements of the assembly to the control engineer; Responsible for 3D and 2D design and calculation of assembly parts; 3. Assembly structure design; Assembly dimension chain calculation; Assembly layout; Assembly optimization follow up 4. Master at least one simulation software (magnetic field, structure, heat, motor, fluid) 5. Assembly test tooling; Assembly test progress tracking; Assembly DV / PV design follow-up; 6. Output the customer technical specification for oil pump / water pump assembly

1. Bachelor degree or above, major in mechanical, electronic and other engineering 2. At least 3 years experience in design and development of the same water pump and oil pump, CFD simulation experience is preferred

1. Responsible for motor control software development of low power brushless motor controller 2. Responsible for control algorithm 3. Develop and study square wave control, FOC / non inductive drive

1. Bachelor degree or above, major in Electromechanical, communication and software 2. Have design experience or professional knowledge related to automotive electronics, and be proficient in C language 3. Experience in brushless motor control, experience in FOC control project 4. Experience in driving brushless motor without position sensor, mastering high-frequency injection method is preferred, and experience in realizing control scheme on Infineon or NXP chip is preferred

1. Be responsible for the implementation of APQP for purchased parts of new projects and the phased approval of suppliers 2. Participation in the review of each stage of new project development and improvement of problem items 3. Assist in confirmation of materials and quality standards in the development stage of new projects 4. Formulation and maintenance of incoming inspection plan for purchased parts 5. Recovery, review and signing of PPAP data of purchased parts 6. Conduct admittance audit and evaluation on potential suppliers 7. Conduct PPAP audit on suppliers and promote the rectification of audit problems 8. Conduct annual audit on suppliers according to the annual audit plan 9. Handling and follow-up of quality complaints of purchased parts in new project and mass production stage 10. Maintenance of supplier performance (monthly and annual) 11. Promote the assistance and capability improvement of risk suppliers as planned 12. Production and output of periodic report data (weekly report, monthly report, etc.) 13. Response to internal audit, customer audit and third-party audit and closure of problem items 14. Handling and reporting of emergencies 15. Formulation and optimization of supplier quality management procedure documents and management specifications

1. College degree or above, major in machinery, electronics and automobile 2. More than 3 years of supplier quality management experience in automotive industry, VDA6.3 certificate is preferred 3. Master five tools and be able to apply them 4. Understand iatf16949 5. Master seven new and old QC tools / 8D / 5WHY and other tools 6. Basic process knowledge (machining, stamping, injection molding, welding, SMT, die casting, etc.)

1. Repair faulty equipment 2. Analyze maintenance faults 3. Formulate and update the maintenance and preservation plan and implement it as planned 4. Implement the equipment management system and technical regulations, guide the operators to use the equipment correctly and maintain it carefully 5. Document management, update PFMEA, control plan, WI 6. Spare parts list update 7. Improvement of downtime rate and defective rate 8. Technician skill improvement training 9. Assist process engineer in pre acceptance and final acceptance of equipment 10. Equipment capacity improvement and OEE improvement

1. Bachelor degree or above, major in electrical / mechanical 2. More than 3 years of maintenance work in automotive sensor industry 3. Master casting, welding, final inspection and assembly knowledge